Very Good 1 5026

Very good device associated with YN-622N-I-TTL no complaints except that the document is not in French especially for those who are not learned English or Chinese !!!
So here's a translation loan can correct damage that illustrations should not be taken into effect

Translation:

YONGNUO YN-622-TX-
Wireless Flash Controller

Contents

General description. . . . . . . . . . . . . . . . . 1
Conventions used in the manual. . . . . . 2
Support Function List. . . . . . . 3
Designation of parts / LCD. . . . . . . . . . . 4
Designation of parts of Start / Quick Guide .5
Preparation before use. . . . . . . . . . . 6-7
Setting. . . . . . . . . . . . . . . . . . . . ... . . . . 8/10
Awakening Flash and tripping. . . . . 11
Other trigger modes. . . . . . . . 12
Output function shutter. . . . . . . . . . 13
Reference. . . . . . . . . . . . . . . . . . . . . . . . 14-15
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . 16
Specifications. . . . . . . . . . . . . . . ... . . . . 17

Precautions

> Turn off the power of all equipment when connecting or installation of the product.
> Keep dry. Do not use the product with wet hands. It is also prohibited to immerse the product in water or expose to rain; otherwise it may not work normally or even be damaged.
> Do not use in explosive situations; violation of this warning may cause an explosion or fire.
> This product includes the battery, be strictly in accordance with the relevant provisions on the use of the battery, otherwise it would cause property damage or injury.

General description

Thank you for purchasing Yongnuo products.
> Wireless i-TTL Flash Controller YN- 622N -TX is for use with the i YN- 622N Wireless Flash Trigger-TTL transceiver.
> This product adopts flexible control LCD menu, the mixed use of the three groups A / B / C i-TTL flash units using, Manual, or super flash sync mode can be set with the exposure compensation or flash output of each group. In addition, it supports the setting different focal length (zoom) of the three flash groups, remote distance can reach 100M, supporting seven wireless channels and A / B / C three groups, and equipped with the transmitter AF-assist beam. Make upgrade the USB firmware.
Compatible with the list of Nikon cameras:
D70 / D70s / D80 / D90 / D200 / D300 / D300S / D600 / D610 / D700 / D750 / D800 / D810 / D3000series / D5000series / D7000series

Included items:

1 × 622N controller YN- -TX
1 × manual
1 × LS-2.5 / N1 shutter connecting cable
LS-1 × 2.5 / N3 connection cable plug

Conventions used in the manual

> This manual assumes that using the camera / flash are compatible and uses the transceiver channel with YN- 622N.
> The Features Supported by the product depend on the camera and the flash used. Regarding the operation of 622N YN- transceiver, camera and flash, respectively read the user manual.
> For the latest firmware and compatibility list and instructions, visit [...]. ? Upgrading to the latest firmware before using (P15).

YN- -TX YN- 622N 622N

The icon below used in this manual
Refers to briefly press the button. Refers to a long press (and hold) the button.

Supported Functions List

LCD, multi quick operation keys?
? The firmware can be upgraded via the USB interface
? Supports the wireless function of the trigger
? The focal length (zoom) of A / B / C three flash groups can be set separately
? Equipped with the development of AF, the pilot lamp (can be disabled) flash mode combinations:
? Enlighten i-TTL / Manual / Super synchronization supports the mixed use of A / B / C three i-TTL Speedlight groups, manual flash, and Super Mode flash synchronization
? The exposure compensation or the flash output of A / B / C of three Speedlight groups can be set separately
? Synchro: first curtain synchronization, second curtain sync and FP high-speed sync, the highest sync speed is 1 / 8000s
? Supports the exposure compensation, and the locking function of the flash output (FVL)
? Supports the simulation (modeling) flash, red eye reduction? Support zoom flash (auto)
? Super Sync (SS) allows the timing adjustment to a larger X-sync speed of the device.
? Settings saved automatically
? The flash sync signal can be entered through the PC port
? Supports flash based trigger (maximum sync speed is 1 / 250s) of the claw has the standard Nikon
* The above functions must be used with the transceiver YN- 622N. The function rooms can refer to the camera manufacturer and flash. (FVL, modeling lamp, flash red eyes, etc.)

Names of parts LCD /

The protective film can be removed.

LCD High-speed sync
Rear curtain
Synchro ZOOM
Flash settings area
i-TTL flash automatic dosing
Electricity Charge Battery
Channel
AF assist beam emitter

Name Start Guide Parts / Quick

A- LCD: Displays all the controller parameters, convenient for your view and configuration.
B- 2.5MM Jack Shutter interface: Wireless trigger function (P.13).
C-AF beam emitter (p.10)
D- PC interface: Flash sync signal input (P.12).
E - USB firmware update via the computer connection (P.15).
F - Mode Button: Each time you press the button in the flash mode (p.8).
Group G button: The arrow shows the group switch settings (p.8).
H - TEST button: press and hold to wake up the flash, short press for flash tests (P.11).
I- Selection / group of buttons: multifunction button group including [Up] [Down] [Left] [Right] and [OK] buttons that can set the channel, zoom, flash output and other parameters.
J- AF / SS Button: Short press to switch AF beam emitter (P.10), long press to [Super Sync] settings (p.9).
K- ZOOM / CH Button: Each short press to switch to the three groups A / B / C (P.10), long press to the channel setting (P.7).
L - On / off switch.
M- Indicator State: bright green light when there is communication, while the bright red light to trigger (or the shutter release?).
N Ring locking and locking pin (P6)
O - Mounting Claw and contacts: (P.6)
P- battery compartment and cover: (P.6)

Preparing to Use

1. Install the batteries

Open the cover and install two AA batteries (not included) depending on the brand, rechargeable batteries 1.2 V can be used.
? Remove batteries when not in use for a long time. Replace both two batteries simultaneously.

2. Installation of the controller to the camera

1). Unscrew the locking ring of the control unit.
2). Slide the mounting claw in the camera's hot shoe.
3). Turn the lock ring in the direction of the arrow,
the locking pin projecting from the bracket.

3.On tension.

Power on when the blades of the switch to [ON].

Preparing to Use

4.Canal Group:

Long press the [ZOOM / CH] and press [Up] or [RIGHT] to increase, press [Down] or [LEFT] to decrease, press [OK] to confirm.
Set the same channel as the transceiver YN- 622N.

5. Transceiver and flash settings:

1). Set the receiver group of the transceiver, and set the same
channel controller YN- -TX 622N.
2). Set the flash i-TTL flash mode *, the flash fires
using the method and the parameters set by the flash controller, i-TTL / Manual flash. (* For non i-TTL flash mode or other trigger mode, see P.12).

1. Groups set modes (remote control)

> Shooting with another flash mode for each group
1) Press the [GROUP] to select the setting group, press the arrow to select the group A / B / C
2) Press [MODE] to set the flash mode for the selected group, each pressure to the parameters as below:
TTL: i-TTL, FEC setting range is 3-3-EV, press the [LEFT] or [RIGHT] to increase and decrease 1EV, press [UP] or [RIGHT] to increase and decrease 0, 3 EV. It is supported to adjust the FEC on the flash, the compensation value is superimposed by flash setting and the controller setting.

M: Manual flash The adjustment range is 1 / 128-1 / 1, press the [LEFT] or [RIGHT] to set, press the [UP] or [RIGHT] for fine adjustment.

SS (Super Sync, refer to P. 9)

(No): The group does not participate in the flash setting.

> When setting the flash mode and settings on the controller, the flash screen on the transceiver will not change.

SETTING

2. About Super Synchro (SS)
> Use the non-high-speed flash synchronization to achieve a higher speed synchronization, this function is applicable to stroboscopic flash, the flash duration is shorter, and devices with auto FP only. Setting Setting the timer setting Super Sync.

1. Set the delay time parameter controller SS:
Press and hold the [AF / SS] to continue the setting, press the [UP] [DOWN] [LEFT] [RIGHT] to adjust, press [OK] to confirm and exit the installation, supports automatic configuration (AU) or Manual Setup 0.1-3.0.

2. Using super Sync:
1). Set the flash to manual mode, press the transceiver using the claw flash or the need of the PC port connection. making the output at full power manual flash (1/1).
2). Set the flash sync speed of the camera as AUTO FP, the maximum sync speed obturator can reach to 1 / 8000s. According to the flash pattern, the output power and the shutter speed
to adjust "SS" parameter controller to adequate delay.
3). Take photos and check if the photos are synchronous, it can see gradations or variations in the photos, the results will rely on the camera and flash.

3. ZOOM Setting

> It supports the setting of the focal length of the flash lamp socket on the controller transceiver.
Each short press button [ZOOM / CH], select one of the groups A / B / C, press the [UP] [DOWN]
[LEFT] [RIGHT] to install, supports setting range: 24 - 200 AU (Automatic), press the button
[OK] to confirm.

4. AF beam emitter
? When using AF in low light, the built-in controller AF beam emitter will be automatically issued to facilitate autofocus.
Briefly press the [AF / SS] button to activate / deactivate the AF beam emitter, the icon appears on the LCD.

It needs to use the AF unit.

Flash alarm clock and trigger

1. Flash Flash revival and trials
When you press a half on the shutter button on the camera or press the [TEST] of the order, the green LED light alarm clock hot shoe on the transceiver out of the enlightenment. When pressing the [TEST], Flash groups that have been selected will be tested once.
2. Flash Trigger
fully depress the shutter button on the camera activates the synchronous flash trigger red light will be bright.

Other trigger modes

1. No - Remote Control Mode:
Set the flash-compatible transceiver in manual flash mode or RPT, the flash will operate according to the mode and the displayed parameters, the controller will not solve the remote control flash mode or exposure compensation (power the flash).
2. PC Interface & Trigger flash-based (non Nikon support body)
> PC interface (input) Trigger:
> Use a LS-PC / PC cable (optional) to connect the controller and the PC interface of the device.
> Basic Flash (simple contact) Trigger: Install the controller into the shoe of the camera.

. 1) The transmission of the group configuration:
Group configuration depending on the controller.

. 2) Flash Mode Configuration:
Set the manual flash (M) by the flash control panel, change the flash manually, use the controller PC or contact with triggering the flash interface, no high-speed sync setting or another TTL function (highest synchronous speed is 1 / 250s or lower).

Shutter button function

? Use the transceiver YN- 622N for wireless transmission, the controller YN- 622N -TX to output the trigger signal.

1). Install the controller YN- 622N -TX claw on the camera, and use the LS-series 2.5 connection cable jack to connect the controller and camera.

2). Press and hold the [TEST] YN- 622N transceiver to focus, release the button
[TEST] to blow. flash installed on the transceiver YN- 622N, is triggered synchronously.
> Supports single.
> If the controller is not installed on the claw of the compatible device, the trigger fires when you press the [TEST] of the transceiver.
The cable is compatible trigger list: LS-2.5 / N1: D200 / D300 / D300S / D700 / D800 LS-2.5 / N3: D90 / D600 / D3100 / D3200 / D5000Series / D7000Series LS-2.5 / N 2 (optional): D70 / D70S / D80
reference

1. Flash Synchro FP:
> Refer to the setting of the camera. Supports first curtain, second curtain synchronization and high speed synchronous (Auto FP *). The corresponding icons appear on the LCD screen (P4).
> Using the high-speed sync must set the flash sync speed of the camera to "AUTO FP". The maximum sync speed is 1 / 8000s or 1 / 4000s (depending on the device).
> Some device models do not support HSS (without optional Auto FP), the shutter speed will be limited to 1 / 250s or less when using this type of device.

2. Backlight LCD screen:
Press any key, the backlight of the LCD screen lights up for 5 seconds.

3. About the battery charge display:
The battery icon in the top right corner of the LCD display shows the electrical charge. In case of low battery, the battery icon is flashing, replace the battery.

4 About the automatic backup feature. :
The controller automatically records the channel settings, grouping, flash mode, AF-assist beam emitter etc.

Reference

5. Reset

Firmware update 6.USB

Hold [MODE] and [AF / SS] buttons simultaneously until the screen shows, depressed and released to restore the factory settings.
1). Visit the official website YONGNUO:
[...]
to download the firmware update software and the latest firmware.
2). Disable. Press and hold the [mode] and on. The display shows the firmware update interface (to display the current version).
3). Connect the controller to the PC via a USB cable - MINIB (not included).
4). Complete the firmware upgrade operation according to the software prompts.

Help

1 voltage fault or automatic shutdown:
> Battery is exhausted or vice versa.
> Install the battery in the correct direction of the battery compartment, and make sure the battery is full and restart power.
2. The flash does not fire
> Make sure that the power of all equipment is full, and the flash is in the ready state (the flash-ready indicator)
> The connection between the controller (transceiver), the camera and flash is reliable;
> That the controller and the transceivers are located in the same channels and even controllable groups.
3 i-TTL or under exposure:
> Make sure the camera body or the flash compensation setting. It may be underexposed if it is greater than the distance flashing effect. It can be on overexposed when TTL and manual flash are used simultaneously, now manual flash may be suitable for use as a backlight.
It is suggested to use the following procedures to deal with other problems occurring with:
1.) Restart all equipment.

2). Replace the batteries of the order and transceivers.
3). Reset all the factory settings of the control and transceivers.
4). Reset all the camera / flash unit factory settings.

Specifications

System Type: Digital FSK 2.4GHz wireless controller
Distance: 100M
Channel: 7
Flash mode: i-TTL, manual flash, Super Sync
Sync Mode: Front-curtain sync, rear-curtain sync, sync speed (Auto FP)
Groups: Groups 3 (A / B / C)
MAX Sync Speed ​​1 / 8000s
Trigger Interface: Claw, PC
Trigger Interface: 2.5MM upgrade firmware part of USB output interface:
AF assist beam of the issuer:
Battery: AAX2 (support 1.2 V rechargeable batteries) 3V Standby time: 120 hours
Dimensions: 89.5 × 53 × 39mm
Weight: 82g
The functions in this manual are based on the test conditions of our company. Further notice will not be given if the design and specifications change.
The YONGNUO logo in this manual includes a trademark or registered trademark of Shenzhen Yongnuo Photography Equipment Co., Ltd. in China and / or other countries (regions). All other trademarks are the property of their respective owners.