Actually, you read first, what you like to read möchte.Das Maschinchen regret to have to learn to walk;

Who are his Bohr and Fräsmaschinchen coinciding with the full speed of his determination,
certainly need not wait long for it until the engine can be supplied to the electronic waste.

That the device has been in some reviews with only one star which has not impressed me directly with rejection product, but they have let me be careful.

Granted:
Was it then but rather the low price, which has made me curious in the light of many satisfied recessions.
,
I (1800 Watt) did until recently my experience in bearing replacement at a very high professional router, I sought thus to the operating instructions for a hint of a possible break-in period and how these should be handled.

Wrong! This does not exist even after repeated searches.

If something is not in the manual, can not be expected that the customer heeded such important things.

And thus it is quite understandable that it is enough for just one minute, then only 1 star for the premature "OFF".

My experience and approach:

Right at the beginning of the first use, should first the speed of the lowest starting and in small steps, be driven high for an extended period to full speed. (1 -1.5 hours)

The (ball) bearing of the rotor is already prone to premature blocking without this measure.

It is even very audible, like the little engine starts over time and gradually to run more freely.
In addition, the carbon brushes have time to shrink, which is also the pleasant sound (decreasing coal fire) can be heard.

Meanwhile, my unit has been running at medium load approximately 12 hours of use, including the supplied belonging flexible shaft, which will be evaluated by me with "good".
The chucks are both good and run exactly centrally.

The grip handle has a too small diameter, which quickly led to clench his hand with me for big hands.

Certainly one or the other alarmed that the tool change suddenly the soul out of the envelope (wave) slips.
But this is introduced just as quickly as it has slipped out.
How many can cite it as a shortcoming in their recessions, is not enforceable by.

Some of the supplied accessories I've GE / ver needs and rate it in terms of quality rather than mediocre.
Krumme shafts of the tool carrier contributed equally with the devaluation, as the poor quality of some tools (abrasive) itself.

The service life of the sanding sleeves for. Ex. Is even "trashy" to designate, with the adapter for this is of good quality.
This becomes even clearer when one uses Ersatzhülsen of the u. Mentioned manufacturers.

Use the tripod's is essential when working with the Flexible Shaft.

Not everyone can afford for lack of space, that this "plastic soft tissue" from apparently stable plastic permanently placed on the workbench or better yet remains bolted to him.

Therefore, I am of the opinion:
A common dismantle, assemble as a particularly solid, easy prohibits the construction and the quality of the material used.
These bends with increasing tightening torque, which means:
The terminal is actually determined never, until everything falls again.
There are, if I interpret it correctly, holes for screw available with the workbench, but most workbenches are anyway too small to even allow a fixed screw mount.

Here really is only one way to avoid having to constantly complain about the terminal must:

Make yourself a copy of MPX (Multiplex).

The telescopic pole with picks for the machine is in another fine.

My Conclusion:

The purchase and operation of this little machine does not have to begin and necessarily coincide with a nasty surprises.
An indication of a break-in period in the manual would the supplier certainly out of trouble.

The more this tends prematurely or rather, to acknowledge their service in the first few minutes, can not be justified with the low price.
While taking the local collection point for electronic waste such things contrary to free, but against the background that led by China, dealing in the world and with our resources, as they did not fall from heaven, even more so.

The customer, and especially the supplier can refer to our recessions or ridicule.

With my experience in dealing with professional machine tools of all kinds, I would like to eventually helped to mediate the customer that it can not be a quality in this product.
That it was enough but for 3 stars simply is because the buyer himself contributes a little to or may contribute by educating them.

The set is in my opinion more favorable than having to call with cheap.

Since there Dremel (Bosch) Proxxon and especially "minipowertool.de" with plenty of good accessories in the market, it is not advisable from a purchase, taking into account the above procedure not necessarily.

For hobbyists, which is only a small budget to work with, this set is totally OK
For if the things once run a couple of hours, she also manages to bring the trendy 130 watts on the good flexible shaft to the tool.

I want to cheat a little trick with the can be bent or drill shafts set up to 5 mm in diameter again.

Man (n) take and span a piece of hardwood (MPX with a thickness = drilling / shaft length up to the chuck measured), with a clamp fixed on the drill table or workbench and drill with crooked drill with a somewhat smaller extent a hole in the wood so deep it goes.
With bent shanks, of course drilled in size of the shaft diameter before.

Then pocketing the crooked drill / shank first few millimeters into the front hole drilled by rotating the chuck by hand.

Then you go electric and low speed further, up to the chuck.
After the drive out of the hole, the drill or tool shank should be directed 1.a again.

The best results are obtained, however, if a drill press is used.

Greeting

Reimund Leuschner