It is delivered disassembled, the pack size corresponds to the lower frame (refer to the upper photo, Orange Motor Unit from, this is the base), the motor unit is packed in the inserted tub.
For assembly, only the two wheels, both feet and the motor unit must be bolted to the base, a total of 8 screws, which can be quite easy tightened within 5 minutes by the enclosed, fully sufficient for this "one-way" tool!
Then cable plug in and off you go!
The tray insert and
****** VERY IMPORTANT ********
****** ******* CLOSE THE WANNENVERIEGELUNG
(According to the dealers, the reason for complaint no. 1, because customers think the engine was in Ar ***, this must "only" the Security Veriegelung be closed !!!)
If power is on it, press the green button and off you go !!
Initially (it is clear ... Who does not ???) reingeschoben what works and tested their performance!
Unprepared it attracts about 5 cm thick, rel. soft hip-road "like butter" pure, and (if you set the right, more on that later), the thin shoots are consistently chopped into 2 cm long pieces !!
Cornelian Cherry shoots and branches are very hard (harder than comparable oak shoots!) Who grabbed the chopper only about 2 cm thick. (No wonder very much as would other rolling chopper early push hard on their border!)
Once plugged, the engine switches off automatically after few seconds to reverse and tried to run freely again.
To again be calling at jurz press direction change key, you're ready to continue, after having arranged differently to the thick branch in the cut hole, or first tapered. (More later)
From the volume wise, it is very pleasant, about how women's mixer in the kitchen! ;-)
If you know how, then you have a wheelbarrow (depending on shredded material) in 10 minutes well heaped full !!
Well applicable to my Tip's, to other chopper !!!
Current:
-Use Only as much power cables, as necessary! I take this this cable:; redirect = true & ref_ = oh_aui_detailpage_o00_s00
Of particular note: 2.5 mm² cross-section !! (The vast majority of cable have "only" 1.5 mm² cross-section)
Thus, the current can most easily reach the chopper, and it is noticeably more power is available!
-The Backup to outlet should be fused with 16 amps and sluggish, it should denoch permanently knock out, you have the following options:
-A Sluggish fuse candle reinmachen (take the blown fuse, go to electricians and say "need for chopping a sluggish assurance than this!" And he knows!)
-If Breakers, can kick it from Electricians a sluggish backup machine !!
-If Apartment and change the fuse box, for example, by landlord is undesirable:
Insert pair of power cables hinterieinander, the more, the carrier! Disadvantage: power goes flutes and easily clogged ... :-(
Blade engagement:
The first time no perfect cutting performance is technically possible because the counter plate and roller blades are mutually not perfect yet "broken in", therefore as described in operating instructions before the first cut very slowly (SLOW !!!) turn the back plate pure until (with flashlight in pan recognizable) aluminum chips comes out! Will not return rotate but left so !!
While it is a bit more aluminum chips come out, but then the striker is set to roll knife work PERFECTLY against each other and "broken in" !!!
Conn. Mark with a white Edding "12 clock" on the dial !!! (Or a small drill a recess schedule)
If possible, as little as possible (preferably not !!!) play on counter-plate setting rum !!
Because with each adjust times new aluminum chips is again unnecessary planed from the counter plate until it breaks at some point !!
Therefore, the mark, so that one after an unavoidable opening of the counter plate (necessary with obstinate constipation!) Again exactly the same can rotate far out! (The best rule of thumb: 3 turn out, Branch rausnehmen, 3 revolution pure until the mark again is set to "12")
Heed to these points, so both thick and thin shoots is always clean chopped to about 2 cm in length! :-)
Constipation / preparation clippings:
There are 2 types of Constipation Cause:
Either the wood too hard (as just thicker Cornel-shoots), or simply just too thick, although it fits up inside ...
For their design fits in between the blades of the cutter block not as much wood as it should ...
This makes it easier and you can get through even tough 4-cm-shoots with minimal effort more!
It starts with the limbing:
Make sure that the drives be chopped from 2 cm have no "coat hook", but is cut off as smooth as possible to drive!
Thicker branches to 4 cm deep 10 cm single column of thick side. ALL must not be split. (In mill the split portion packs next to each other more easily than if it has to chop as a whole, because it can be distributed better between the blades)
Even when limbing with the loppers to remember the effort! From a certain amount of force and the chopper itself is struggling, so split or separate the specific shredder for branches with shoots next to thinner shoots.
The larger cut shredded so that the shoots of the main driving protrudes only Fan Shape, and not extending to all page. (So it runs easily in the slot-shaped Häckselloch a!)
My shredder way, I have brought me directly from HBH (there are about 20 Km away from me), which also offer 2nd choice and self-propelled foragers for sale on, mine cost as 2nd choice (previously found "deficiencies": a lack of blind rivets on base) measly 145 euros!
Price-performance ratio UN BEAT BAR !!!
Only if you know how you have to work with the harvester, it packs be wonderful job !!! :-)
After all, one is with a purchase of a Ferrari and not automatically a World Cup candidate, but you have to collect only experience and training !!!
Therefore, 5 stars !!!