I have yet tried it in the shop and had to find that the Dyson to be attached to any of my tools (Bosch table saw, Bosch sander, Bosch grinding mouse, Einhell Router).
With some tape I could him but then encourage them to form a bond with the Einhell router, but after some milling work I was still wrapped from head to toe in chips.
Here the Einhell sucker its strengths. For the first course, he fits perfectly on the Einhell router, but on the other hand he really sucks every chip a. It fits even on the table saw, but unfortunately does not my sander.
However, that does not matter, because thanks to its high suction, the suction holding by the Unterdrock all by itself.
And I stress again, the hose does not fit to the grinder and is too large (beiligender adapter, however, is too small). And yet I can wonderful, carefree grind. The suction hose sucks at bombenfest !!
Since the Dyson can pack.
The automatic circuit I use very happy. An operation less in order to you have to worry.
I would like the sucker firmly integrated into my workshop cabling and a power strip connected (with me only one device is active immern;. But I will not always have to reposition the plug)
But unfortunately it does not work quite as desired. Every now and then there are activities for which I do not just want to use the vacuum cleaner (short drill a small hole with the drill example, which I had previously used with suction and Forstner bit)
But unfortunately the socket on the vacuum cleaner will only flow as long as it is set to automatic. If the vacuum cleaner to "Off" is the socket dead. that annoys a wenig.Gerade if you abused the sucker at Autoaussaugen as extension cord.
But that may be necessary to deal.
My wife laughed at me though. as I bought a second sucker, but I am sure they too will appreciate the merits at the next author to some.
What I miss, however, is a flat upholstery brush or a small carpet brush. I like to use to clean my workbench.
The floor brush, however, seems to me on the small side. The my Dyson is almost twice as long.
Where should I suck with the Dyson only once, I need two suction operations for the Einhell.
As for the dust collector, I am completely thrilled; because fit neatly into sawdust.
I always use the vacuum cleaner but with filter bags to protect it from sanding dust (non-woven bags are already ordered and still waiting for delivery - which are able to absorb the swarf better, they say)
Because, unfortunately, lost a lot of capacity through the pleated filter and unfavorable, but cheap construction, the filter bag. But to be honest. In 30L stainless steel tank, I can live with it, that I might "only" can be used 15l. This is after all still 30 times by Dyson !!
So then once wanted to know Conclusion, for those who shy away from the big block of text up there and immediately the most important:
Positives:
+ High suction power - keeps itself constantly on grinders, though tube actually too big
+ Lots of storage space for accessories on the vacuum cleaner itself - and all provided with pictures.
+ High Capacity
+ Volume actually not that high. Not much louder than our old Dyson.
+ Stainless steel suction pipe. Even with many expensive suckers nowadays plastic.
+ Langer, lightweight, highly flexible hose
Neutral:
o Tool adapter does not fit Bosch grinders - which is certainly more likely to blame Bosch. But thanks to high absorbency, it is nevertheless.
o hose apparently without steel spiral. But for that easy.
o Should thanks adapter nozzle with many accessories tolerated by other manufacturers
Negatives:
- Contain no flat upholstery brush
- Contain no Blas adapter, or Available. I'm going to try from Nilfisk
- Carpet brush too narrow
- No power to receptacle when suction is set to "Off".
- Manual does not address the storage facilities for adapter on suckers and their purpose. Also, as the cable management is intended, is not mentioned.