The Beast ... has persevered!

The widely varying reviews for this sense have me sometimes to write what motivated ...
I have read the reviews before I bought the BC52. So no excuses. There are also various YouTube. Videos to BC52. Brickwork.
Thus, it was clear nothing but double check "out of the box" and going on, everything sharp and check for missing, loose, misplaced parts. So far so good. The delivery was accustomed quickly unpacking no findings, except that everything was safe and completely available. It has apparently reworked in detail, often criticized thing with the choke for example, was correctly labeled, it was not a screw at an angle or wrong in it, all threads ok, everything processed quite useful in particular. Although div. Parts (blade guard, guide handles, throttle / control unit) call for cautious handling. We'll see ...
Before the first start I have done the following things:
- Expanded spark plug, a little oil in the cylinder, a few times by pulling, candle remounted,
- Controls all covers on the engine and the carburetor and exhaust area for tightness of all screws
- Mounted handles. The throttle promptly lacked a housing screw. Matching replacement screw was on hand ...
- All screws and thread in handle / holder area ok
- Expanded all drive shafts and lubricated with Molykote grease (preventive)
- Cutterhead via grease nipple filled to the grease discharge on the blade side bearing, based on the filled amount could not have been much in it ...
- Then mounted the knife very nice to mount everything to take care is to centric seat of the knife!
- Oh, the orginale tool disposed to the spark plug wrench immediately ...
- 1:25 mixture (Best Super, Stihl 2-stroke oil) filled, tightness controls: Ok.
- Was on the carburetor the fuel pump operates up through the return line to see.
- Switch to ON, searched the compression on the starter, 2 trains tight rein --- !! I have also already experienced differently. Excellent!
- About 5 minutes with small gas shocks (no high speed!) Warm up, then ...
- From the grounds, demolition plot with lignified ca 50 cm high vegetation ...
---> Runs through clean. Initially cautious, not full load, but it's quite good! Smokes always less.
---> No excessive vibrations in the middle speed range almost none.
---> After about 20 minutes of changing load, number of shutdowns is to the to the belt and the handles properly set ... no problem
---> Starts hot, lukewarm, cold on the first train! (My 52 BC halt ;-)))

1. Conclusion:
After 1 hour mowing the thicket: Everything is still off, nothing dropped, always run better, you realize as the engine begins to run freely. Let's see this, it will continuously provide supplements in this evaluation.
Compared to currently available NoName String trimmer with 32ccm engine already much better pulling power and you are not forced always handle everything about full speed, half-gas rich often. Let's see how it presents itself when the motor is free running properly. The knife cuts all ... gladly wire mesh and the like without complaint .... so watch out!
The device is definitely suitable if one is clear that prevention must be made, many simply can not be high-level quality at the price. Cautious 4 stars now times.

go on ...

After another 2 hours of work in the field, many dekupierten ants and mole dwellings, various Crushed stones I made the thread machine to mount ....
What can I say: rubbish!
The original thread was zimmlich expeditiously, the Sense vibrated strongly as the thread roll is not centered running. After a refill with 2,7mm Stihl thread the thing has then broken at the first thread cutting the blade guard into its component parts. The cutting knife at the blade guard and half the plugged lower blade guard was gone. Have the knife remounted and adjusted to protect it. What a difference: The Sense running with the knife just super and very low vibration.

Conclusion so far:
Using the 3-zag knife: Well, now with the shortened protection is even very good. It's fine.
String head = total failure. The would also be hiked without self-destruction in the trash, because very bad centeredness.
I had procured me an alternative of Oregon. Test this on Saturday. There are again to mow approximately 1200m², the finale of this year.
The engine has been running much better now after I set him slightly leaner. The little machine now hangs great on gas and draws well. Also the fuel consumption is very fallen significantly, as many now with 1/4 - 1/2 gas can be processed. There are still all the parts off, nothing loose or fall on.
If the Sense creates Saturday without discomfort I will procure a 2. As for spare parts, also to change by the additional front quickly between thread and meter operation without major installation to.

Addendum mid-November:
have now cleaned the Sense and checked for clearing away. Everything is still at it and nothing got broken. Nothing knocked or wobbly!
Since the first conclusion yet about 6 hours of operation were made up. 3 with the OREGON 2 - trimmer head. Also hereby the Sense runs very quietly. But needs more power because I'm doing the strings a bit longer .... faster mowing and you do not often exchange yarns. For me so perfectly!
The engine is now running top notch, really snappy. Have adjusted it since the beginning of even more times on the carburetor setting
The fuel consumption is now at about half from the beginning. The engine also depends very clean on gas and draws fed through. Very good. Pouncing always train at 2 starter.
Be gentle and good shrinking supplies easily worth still !.
As already indicated above, I order even after a BC52 as parts support, want to be called: I am satisfied BC52 user.
It remains Final at 4 stars because simply more attention must be made from the outset, as in modern appliances usual.
Who is willing to do this can get involved with the BC52.