Review Tronje A8050

I hang my LG 50 PG 6000 on the wall yesterday.

My specification was as follows:

1. I wanted to come to the terminals and thereby see something! (Hate this blind Rumgefummel behind a TV)
2. 10cm distance from the wall (so is the manual for the development of heat)
3. Absolute rigidity! The TV should always hang grade, regardless of the position !!

No need but would be nice:
Pan, tilt and telescopic.

After I have read in various forums by holders who are easily bent, I was looking for the same for a lot more that can carry as the plasma really weighs. This weighs 40 KG without feet, with feet 43 KG.

So came only a bracket with a certainty of minutes for me. 1.5 into question. So about 60 KG. I then became aware of the Tronje A8050, which can carry 85 kg proud and full tilt, pan, tilt and telescopic. I have an unbeatable price of just 163 times incl. Bought this last week shipping.

Technical specifications of Tronje A8050

Full-Motion Wall Mount for: prefer tilt and swivel
for flat screens from 32 "- 65"
max. Capacity: 85kg
Distance from the wall: 550mm 105mm-
Hole spacing: max. 810x500mm
follows the VESA standard specifications
Material: steel / aluminum
Weight: 15,4kg
Dimensions (WxHxD): 870 x 524 x 105mm
Tilt angle: +/- 15 °
Rotation angle: +/- 60 °
Quick release for locking
with cable management

I was only a little worried when the package arrived. the board looked very taken. I only thought it would be a returns but after examination of the wallboard was clear that this was never used. No screws or similar footprints. Everything was also bagged clean and pressed in Stüropor.

the first impression:
Solid! Very solid! I knew by then only these non-pivoting brackets that are stamped out "sheet". The single "sheet metal" are the tracks that are to be screwed to the plasma and approximately 5-6mm thick base plate which is fixed at 8x 12mm dowels on the wall. The swivel arms are more like a wishbone to a car! In general everything seems to be cast. Not for nothing weighs only the holder 15KG! The design is very simple and the mounting plate is hidden after installation behind a black plastic cover.

Now the building came:

Here also began already "my" problem:
Does anyone know Murphy? So with the law because of "It always turns out differently?" ;)? Only the battery percussion drill was empty, then was in the toolbox not the drill set, after a long search and a lot of swearing, I then found this. Unfortunately was the biggest a 10mm, but I needed 12mm .... Hmph! Then I still found a 12mm drill bit but unfortunately not a stone, but only metal drills ... Harg !!! Of course it was also a public holiday. I simply drilled with rock drills and the last bit, gescharbt with the now hopelessly blunt, metal drill out. Of course, had the battery in the last 2 holes again floored ... Half an hour was too little load ^^, thank Murphy !!! : |

Here is one more time the display properly think the people praise in Tronje. Thanks to the drilling template, which I have aligned with a spirit level on the wall, the holder depended absolutely flat bonded to it. Now some criticism of Tronje: the dowels are absolute cheap-Baumarkt-Grabelltisch scrap. in 3 of 8 holes were turning with the screw. There I filled Montagefix and after drying the then screw tightened. Buy some better at the hardware store around the corner which the brand manufacturer.

Now that everything hung on the wall, I have this first "tested". I thought to myself: Before I since my expensive plasma hanging off, I try the first part of. About me: 31 years old, 184cm. 92kg. Thought, done! I have the support not fully extended, due to the extra 10 kg ^^, and I've just been hanging dull times to the part on it.

It held, from the feeling has since also yielded nothing. After this test, the self-test, I then "ALONE") set my plasma on the rails. This is also achieved beautifully. Simply lift a Bissel over the rails, can slow down and even hanging the TV on the wall (2-3cm deep hooked). You can also raise a safeguard against reinstalling but I've saved me. This is simply screwed. Really is not necessary. When he then hung the foot was unscrewed. According to instructions of the plasma should I put this on the scene on a soft surface 'Ja ne. is clear 'everything went smoothly.

The test with the water level was then: Whether undressed to angled corner to the dining table or on the wall: the TV is always dare say hangs perfectly straight on the wall. Top! There is nothing to absolutely rigid! The screws for the tendency of course you have been a little harder in order to attract the non-direction floor shows. However, since these were 2 clamping screws, the holding but also still limited.

My Conclusion:

I am, heavily inspired terms this support to the anchor. Top, Top finish, top function. Despite the 50 inch I can leave my TV stick out almost at a 45 ° angle from the wall in the room. Although it looks not really inspire confidence from (such a monster from TV hovers quasi in the air) but it works. ^^ I highly recommend this mount any who is not willing to pay for high-priced in various Elktogroßmärkten. Ahalterungen in electric markets have this weight / Verabeitungsklasse cost to 400!

Rating: very good with star .... except the anchors ^^

Processing: 9.9 out of 10 points (because of poor anchor)
Design: 10 out of 10
Handling: 9 out of 10 (a kind of tension lever for inclination would have been nice instead of the allen wrench)

Result: 10 of 10 points (the dowels neglected)